Quick Change Photo-Eye Is Ideal Replacement For 3" Diameter Lamp Posts.
Quick-Connectors Instantly Connect Female To Male And Provides 3-Wire Solid Connection. Photo-Eye Requires 1-3/8" Diameter Mounting Hole.
Photo-Eye Works With CFL, Incandescents, Mercury Vapor, Metal Halide, Sodium Vapor, LED, Halogen And Fluorescent Bulbs.
Discourages Intruders By Automatically Lighting Grounds At Night Time.
Nothing To Set. No Seasonal Adjustments To Make. Activates With Natural Sunlight.
Rugged Design, UL Tested for Minimum 6,000 Cycles (16.4 Years Daily On/Off) At 500W Tungsten & 850VA Ballast Loads
Features
Technical Specs
Use With 3”-Diameter Lamp Post Having 1-3/8” Diameter Pre-drilled Hole and Two Screw Mounting Holes
Read All Instructions Completely Before Beginning Installation.
CAUTION: TO PREVENT INJURY FROM ELECTRICAL SHOCK AND POSSIBLE RISK OF DEATH, POWER MUST BE TURNED OFF AT THE MAIN CIRCUIT BREAKER OR AT THE MAIN FUSE BOX BEFORE INSTALLING PHOTOCONTROL.
Connect the red wire from the PhotoControl to the black wire of the light fixture.
Connect the black wire from the PhotoControl to the black (hot power supply) wire.
Connect all of the white wires (neutral) together.
The body of control must be located inside 3” lamp post. Insert unit through the hole and tighten two screws enough over the gasket to make a weatherproof seal. If the surface of post is uneven, apply RTV silicone rubber sealing compound before installing photocontrol.
Turn power on. Control has up to 2-minutes delay when turning the power On/Off.
Use only U. L. Listed wire connectors (not included). All metal strands of wires MUST be completely inside wire connectors. Wrap electrical tape in multiple layers to further secure the connections.
Quick-Connectors Instantly Connect Female To Male And Provides 3-Wire Solid Connection. Photo-Eye Requires 1-3/8" Diameter Mounting Hole.
Photo-Eye Works With CFL, Incandescents, Mercury Vapor, Metal Halide, Sodium Vapor, LED, Halogen And Fluorescent Bulbs.
Discourages Intruders By Automatically Lighting Grounds At Night Time.
Nothing To Set. No Seasonal Adjustments To Make. Activates With Natural Sunlight.
Rugged Design, UL Tested for Minimum 6,000 Cycles (16.4 Years Daily On/Off) At 500W Tungsten & 850VA Ballast Loads
Features
- Excellent Replacement Photo-Eye For Pole Lamps With 3" Diameter
- Works With CFL, Incandescents, Mercury Vapor, Metal Halide, Sodium Vapor, LED, Halogen and Fluorescent Bulbs
- Discourages Intruders By Automatically Lighting Grounds At Night
- Saves Energy, Bulb Life, Electricity & Money By Automatically Reducing Daily Operating Time
- Activates With Natural Sunlight, No Adjustment Needed For Daylight Savings Time
- Built-In Time Delay Eliminates False On/Off Due To Lightning And Stray Car Lights
- UL Tested for Minimum 6,000 Cycles (16.4 Years of Daily On/Off) at Maximum Possible Rated Electrical Loads
- Heavy Duty Capacity: Max. 500W Tungsten, 850VA Ballast 120VAC 50/60 Hz
Technical Specs
- Extra Large Capacity: 500W Tungsten, 850VA Ballast 120VAC 50/60 Hz
- Works With Incandescent, CFL, Mercury Vapor, Metal Halide, Sodium Vapor, Halogen, LED and Fluorescent Bulbs
- Automatically ON at 1 +/-0.5 Foot Candle & OFF at 6 +/-0.5 Foot Candles
- UL Tested for Minimum 6,000 Cycles (16.4 Years Daily On/Off) At Minimum 500W Tungsten & 850VA Ballast Loads
- Unit Provided With Color Coded Lead Wires
- For Correct Operations & To Avoid Permanent Equipment Damage, Installer Must Connect All 3-Wires Exactly As Diagram Shows On The Unit
- Built-In Safety Time Delay: 20 to 100 Seconds
- Rugged Outdoor Operating Temperature Range: -40F to +158F (or -40C to +70C)
- For Installing Photoeye Need Hole Size: 1-3/8" Diameter At Lamp Post
- Excellent On/Off Ratio: 6
- Low Average Power Consumption: 0.8W
- Must Install Unit Inside 3" Diameter Outdoor Lamp Post.
- UL Listed Under Our File No. E322033
- Meets UL Standard 773A
Use With 3”-Diameter Lamp Post Having 1-3/8” Diameter Pre-drilled Hole and Two Screw Mounting Holes
Read All Instructions Completely Before Beginning Installation.
CAUTION: TO PREVENT INJURY FROM ELECTRICAL SHOCK AND POSSIBLE RISK OF DEATH, POWER MUST BE TURNED OFF AT THE MAIN CIRCUIT BREAKER OR AT THE MAIN FUSE BOX BEFORE INSTALLING PHOTOCONTROL.
Connect the red wire from the PhotoControl to the black wire of the light fixture.
Connect the black wire from the PhotoControl to the black (hot power supply) wire.
Connect all of the white wires (neutral) together.
The body of control must be located inside 3” lamp post. Insert unit through the hole and tighten two screws enough over the gasket to make a weatherproof seal. If the surface of post is uneven, apply RTV silicone rubber sealing compound before installing photocontrol.
Turn power on. Control has up to 2-minutes delay when turning the power On/Off.
Use only U. L. Listed wire connectors (not included). All metal strands of wires MUST be completely inside wire connectors. Wrap electrical tape in multiple layers to further secure the connections.